PARTING OUT - 1990, 1995, 1997 4RUNNERS and 1988 FJ62
#1
Registered User
Thread Starter
PARTING OUT - 1990, 1995, 1997 4RUNNERS and 1988 FJ62
I need to clean up my back yard.
1990 4Runner (5 speed, 3.0, 4x4) – Brown Interior, Gold Exterior
The following have been sold already. I have everything else. It has the swing-out tire carrier also.
1995 4Runner (Auto, 3.0, 4x4) - Brown Interior, Gold Exterior
This was my beater. I still have most of the exterior and interior stuff.
1997 4Runner (Auto, 3.4, 2x4) – Brown Interior, Silver Exterior
I purchased this for the motor. I still have everything but the seats and interior door panels. This truck was in a front impact crash so there is no hood, or fenders. All of the front suspension stuff looks good.
1988 FJ60 Land Cruiser
Got this for the front axle. There's not much left but it does still have a few parts left. The body has a lot of rust.
Please post what you are looking for below. I will see if I have it and post a price.
I will try to keep this post updated with what has been sold as it's sold.
1990 4Runner (5 speed, 3.0, 4x4) – Brown Interior, Gold Exterior
The following have been sold already. I have everything else. It has the swing-out tire carrier also.
- Transmission / x-case – SOLD
- Seats – SOLD
1995 4Runner (Auto, 3.0, 4x4) - Brown Interior, Gold Exterior
This was my beater. I still have most of the exterior and interior stuff.
- Motor – SOLD
- Transmission / x-case – SOLD
- Front Suspension – GONE FROM SAS
- Rear Suspension- GONE FROM SAS
- Tailgate – SOLD
1997 4Runner (Auto, 3.4, 2x4) – Brown Interior, Silver Exterior
I purchased this for the motor. I still have everything but the seats and interior door panels. This truck was in a front impact crash so there is no hood, or fenders. All of the front suspension stuff looks good.
- Motor – GONE
- Seats – SOLD
- Mirrors – SOLD
- Interior Door Panels – SOLD
- Center Console - SOLD
1988 FJ60 Land Cruiser
Got this for the front axle. There's not much left but it does still have a few parts left. The body has a lot of rust.
- Motor Head – SOLD
- Front Seats – SOLD
- Transmission – SOLD
- Front and Rear Axles – SOLD
Please post what you are looking for below. I will see if I have it and post a price.
I will try to keep this post updated with what has been sold as it's sold.
Last edited by yotaman; 02-16-2011 at 08:40 AM.
#5
Registered User
Thread Starter
I have the cruise for both 3.0's. I'd have to check on the 3.4. $20.00 for the cruise sound fair?
#6
Here's what I am looking for from the 97:
Spare Tire Winch
Parking Brake hardware - bell cranks, bell crank boots, etc, cable mounts, and associated little parts. Whole cable with bell cranks is ok too.
Rear Hatch Striker assembly - the part on the door, and the mount on the floor panel (mine are super rusty).
Gas tank skid plate - Is there any rust on it? If no, I'd love to see what shipping would run.
Spare Tire Winch
Parking Brake hardware - bell cranks, bell crank boots, etc, cable mounts, and associated little parts. Whole cable with bell cranks is ok too.
Rear Hatch Striker assembly - the part on the door, and the mount on the floor panel (mine are super rusty).
Gas tank skid plate - Is there any rust on it? If no, I'd love to see what shipping would run.
#7
Registered User
Thread Starter
Here's what I am looking for from the 97:
Spare Tire Winch
Parking Brake hardware - bell cranks, bell crank boots, etc, cable mounts, and associated little parts. Whole cable with bell cranks is ok too.
Rear Hatch Striker assembly - the part on the door, and the mount on the floor panel (mine are super rusty).
Gas tank skid plate - Is there any rust on it? If no, I'd love to see what shipping would run.
Spare Tire Winch
Parking Brake hardware - bell cranks, bell crank boots, etc, cable mounts, and associated little parts. Whole cable with bell cranks is ok too.
Rear Hatch Striker assembly - the part on the door, and the mount on the floor panel (mine are super rusty).
Gas tank skid plate - Is there any rust on it? If no, I'd love to see what shipping would run.
I have all the parking brake stuff? I'm not sure what a bell crank is but how's $65.00 for everything from the pull up part all the way out to the axle sound?
The gas skid plate is in good condition. No major rust that I could see. May have a small dent. How's $40.00 sound?
My best guess on shipping would be around $50-$75 for everything listed above.
Trending Topics
#9
Registered User
Thread Starter
#13
Registered User
Join Date: Feb 2011
Location: Upstate NY
Posts: 15
Likes: 0
Received 0 Likes
on
0 Posts
Need a clean fuel pump bracket unit
Hello, new to the forum, old to everything else. Stranded in the salt belt...lost the return hard line off the top of the fuel pump tank seal cover. How much for a clean 2nd gen. fuel pump bracket unit, don't need the pump, just the bracket out to the soft line. Thanks, Andy 12308
#14
Registered User
Thread Starter
Hello, new to the forum, old to everything else. Stranded in the salt belt...lost the return hard line off the top of the fuel pump tank seal cover. How much for a clean 2nd gen. fuel pump bracket unit, don't need the pump, just the bracket out to the soft line. Thanks, Andy 12308
#16
Registered User
Thread Starter
#17
Registered User
Join Date: Feb 2011
Location: Upstate NY
Posts: 15
Likes: 0
Received 0 Likes
on
0 Posts
Fuel pump carrier bracket
I see my request was a little vague.....I'm looking for the in-tank bracket that supports the fuel pump. There is a flange on the top of the tank with 7 bolts and this is where the supply line starts. There is another nipple for the return brazed on the top of this flange, where mine is rusted through. I'm in the process of fabbing up a new line, but please give me a price for this part for when the temps are higher than 2o degrees in my garage. Thanks, Andy
#18
Registered User
Join Date: Jan 2007
Location: Boston, MA
Posts: 62
Likes: 0
Received 0 Likes
on
0 Posts
Can you email me a pic of the steering wheel and column? Nottastalker@yahoo.com
#19
Registered User
Thread Starter
Can you email me a pic of the steering wheel and column? Nottastalker@yahoo.com