2.4 to 2.7 engine swap

Memo · 10-29-2009, 12:23 PM

I have a 1994 pick up with a 22r 2.4 4cyl would it be too much troulbe to change out for a 2.7 4cyl from a 1997 pickup .I have all parts from 1997 truck .what changes will I have to do

This ad is not displayed to registered members.
Register your free account today and become a member on Yotatech!

muddpigg · 10-29-2009, 12:51 PM

Think seafarenman had the 3.0 replace for a 2.7L.

Here a build link to http://www.pirate4x4.com/forum/showthread.php?t=475469

You should post introduction to yourself, welcome to YT

vital22re · 10-29-2009, 01:26 PM

the exhaust routes to the opposite side, you'll need to do some wiring. pressure side of fuel line. Dont know about the a/c. Not sure about bolting up to your current tranny and the 2.7 transfer case has the output for the front drive line oposite of your currant set up. I'm not sure about the motor mounts either may be lucky and just swap the motor mounts from your 2.4.

1987 toyoda · 11-15-2009, 10:50 PM

i have a 1987 toy pickup with a 22re and an a tranns out of an 84 it has dual t cases sased 529s its how i want it i would like to do the 2.7 3rz swap im looking for parts now i have the engine but ORS is shut done for good and i need the harness or can i do the whole taco dash will it fit i also want to know if the bell housing with bolt up and motor mounts i would like to know how hard and how much time it will take to do this

10-29-2009, 12:51 PM	#2 (permalink)
muddpigg Registered User Join Date: Mar 2007 Location: injured and stateside :( Posts: 1,388	Think seafarenman had the 3.0 replace for a 2.7L. Here a build link to http://www.pirate4x4.com/forum/showthread.php?t=475469 You should post introduction to yourself, welcome to YT __________________ http://www.youtube.com/watch?v=rqtr_RvR3sY Balljoints for sale. Open to trades and offers. http://www.yotatech.com/f11/ball-joi.../#post51278784

10-29-2009, 01:26 PM	#3 (permalink)
vital22re Registered User Join Date: Feb 2006 Location: kirkland washington Posts: 677	the exhaust routes to the opposite side, you'll need to do some wiring. pressure side of fuel line. Dont know about the a/c. Not sure about bolting up to your current tranny and the 2.7 transfer case has the output for the front drive line oposite of your currant set up. I'm not sure about the motor mounts either may be lucky and just swap the motor mounts from your 2.4. __________________ 92 toyota truck 3.4 5spd 4.56 gears magna flow cat and muffler2 1/4 piping isr mod to intake 1.5 bjsfront add a leafs and 2inch lift shackles rear rancho shocks all around sitting on 265/75/r16 nitto terra grapplers

11-15-2009, 10:50 PM	#4 (permalink)
1987 toyoda Registered User Join Date: Nov 2009 Posts: 1	the swap i have a 1987 toy pickup with a 22re and an a tranns out of an 84 it has dual t cases sased 529s its how i want it i would like to do the 2.7 3rz swap im looking for parts now i have the engine but ORS is shut done for good and i need the harness or can i do the whole taco dash will it fit i also want to know if the bell housing with bolt up and motor mounts i would like to know how hard and how much time it will take to do this

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search