Brake Drum Removal Help
#1
Registered User
Thread Starter
Join Date: Jul 2008
Location: Bozeman, MT
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
Brake Drum Removal Help
Hey everyone,
I've got a REALLY stuck rear brake drum that won't pop off despite my increasingly drastic tactics. I've read through all the threads I could find and tried everything: backed off the star adjuster all the way... the threaded holes are stripped on the drum face, tried to tap them bigger but stripped again. BFH all around the drum, won't budge despite having been soaked in PB Blaster all night. Tried prying against the back plate, just bends the plate. Even dremeled a small hole in the back plate near the rim of the drum, but a stout screwdriver and hammer from behind won't move the thing. E-brake is off.
I'm running out of ideas and I don't want to cut the drum off.
Sorry about starting a new thread... this is driving me crazy.
Any suggestions?
Thanks, Scott
I've got a REALLY stuck rear brake drum that won't pop off despite my increasingly drastic tactics. I've read through all the threads I could find and tried everything: backed off the star adjuster all the way... the threaded holes are stripped on the drum face, tried to tap them bigger but stripped again. BFH all around the drum, won't budge despite having been soaked in PB Blaster all night. Tried prying against the back plate, just bends the plate. Even dremeled a small hole in the back plate near the rim of the drum, but a stout screwdriver and hammer from behind won't move the thing. E-brake is off.
I'm running out of ideas and I don't want to cut the drum off.
Sorry about starting a new thread... this is driving me crazy.
Any suggestions?
Thanks, Scott
#5
Registered User
Thread Starter
Join Date: Jul 2008
Location: Bozeman, MT
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
Thanks for the quick replies,
I've been BEATING on this thing for hours, gave up the rubber mallet and switched to 3 lb mini sledge, still nothing.
Turning the star wheel down loosens it, right?
Scott
I've been BEATING on this thing for hours, gave up the rubber mallet and switched to 3 lb mini sledge, still nothing.
Turning the star wheel down loosens it, right?
Scott
#6
Contributing Member
iTrader: (3)
Sure fire way is to unbolt the axle from the housing (4 nuts behind the backing plate), pull the axle out and then drop it straight down, wheel studs first, onto a block of wood or smooth concrete. Start out low and slowly increase the height of the drop until the drum pops loose.
#7
Its tricky to turn the star wheel....you have to pry the stop bar out of the way, then turn it the opposite way of the smooth edges...basically, against the grain. Its a PITA and takes a while, but it can be done.
And all that in a space about this big:
( ------ )
And all that in a space about this big:
( ------ )
Trending Topics
#9
Registered User
Thread Starter
Join Date: Jul 2008
Location: Bozeman, MT
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
DeathCougar,
I bought the star wheel adjuster tool because I couldn't get the thing to turn with two flatblades... you're right it's a royal pain. With one flatblade on the ratchet stop and the special tool on the star, it rotated easily. It won't turn down anymore so I think the shoes are backed off all the way.
Still no luck, though. Might try 4crawler's way, should probably change diff fluid anyway.
I bought the star wheel adjuster tool because I couldn't get the thing to turn with two flatblades... you're right it's a royal pain. With one flatblade on the ratchet stop and the special tool on the star, it rotated easily. It won't turn down anymore so I think the shoes are backed off all the way.
Still no luck, though. Might try 4crawler's way, should probably change diff fluid anyway.
Last edited by ShredTheGnar; 07-29-2008 at 12:40 PM.
#11
Assuming that you turned the adjuster the right way...Smack that sucker with a bigger hammer. I've had to pop them pretty hard to get them to break loose. I usually put the lug nuts on the studs to protect them from the hammer.
You will hear it when it breaks free while pummelling it with a BFH.
Good luck.
You will hear it when it breaks free while pummelling it with a BFH.
Good luck.
#12
Registered User
Thread Starter
Join Date: Jul 2008
Location: Bozeman, MT
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
Alright I got the f$%^&* thing off!!
Took an absolute SMASHING with the 5 lb sledge, but it finally came. It definitely helped to bash with a big screwdriver from behind, thru a dremeled hole in the back plate (... now I'll have to seal that up), in case anyone else with a stuck drum reads this thread.
Thanks guys for the advice. I've been soaking up a lot of awesome info on this site for about a year now, but just today I became a proud YotaTech member! I hope to have the 4Runner for a while (it's a baby at 166,000 mi), so you'll see more of me...
Thanks,
Scott
Took an absolute SMASHING with the 5 lb sledge, but it finally came. It definitely helped to bash with a big screwdriver from behind, thru a dremeled hole in the back plate (... now I'll have to seal that up), in case anyone else with a stuck drum reads this thread.
Thanks guys for the advice. I've been soaking up a lot of awesome info on this site for about a year now, but just today I became a proud YotaTech member! I hope to have the 4Runner for a while (it's a baby at 166,000 mi), so you'll see more of me...
Thanks,
Scott
#14
Registered User
Just for reference:
Easy way to back off the star adjuster is to use a L shaped item (o ring pick works, or maybe an allen wrench) and feed it back into the adjuster hole and over the adjuster shaft (you cant see this, just feel for it). Push the lock plate outboard, then use a flatblade to turn the starwheel down (handle of flatblade moves up).
Easy way to back off the star adjuster is to use a L shaped item (o ring pick works, or maybe an allen wrench) and feed it back into the adjuster hole and over the adjuster shaft (you cant see this, just feel for it). Push the lock plate outboard, then use a flatblade to turn the starwheel down (handle of flatblade moves up).
#17
Registered User
Except the OP's were stripped out, ma'in. And, that doesn't always work in extreme cases. It is possible to warp the drum.....or even strip out the threads.
#20
Registered User
Ah! DC's post reminded me of a tip I learned growing up and learning to work on cars in the Rustbelt. Before you install the brake drum, paint the axle flange face with anti-seize along with the wheel studs. Cover all the metal, but don't goop it on so thick that it will sling out into the drum. This will keep the drum from rusting on to the axle shaft. Much easier to remove after the next winter.