Anyone have these hiclearance fenders on an 89-95?
#1
Registered User
Thread Starter
Join Date: Jan 2007
Location: Point Pleasant NJ
Posts: 628
Likes: 0
Received 0 Likes
on
0 Posts
Anyone have these hiclearance fenders on an 89-95?
#4
Contributing Member
Join Date: Feb 2007
Location: maple ridge, British Columbia, Canada
Posts: 9,055
Likes: 0
Received 9 Likes
on
5 Posts
Corey aka Slacker is the owner of that company out in pentiction bc.
great guy, I bought some sheet metal parts from him
I would think the high cut front fenders would look wierd with the low cut rear's as from the factory the rears where cut 1" lower.
But if you are going for the sas'd pre-runner look,
great guy, I bought some sheet metal parts from him
I would think the high cut front fenders would look wierd with the low cut rear's as from the factory the rears where cut 1" lower.
But if you are going for the sas'd pre-runner look,
#6
Registered User
Thread Starter
Join Date: Jan 2007
Location: Point Pleasant NJ
Posts: 628
Likes: 0
Received 0 Likes
on
0 Posts
They arent that much. 200 canadian is like 130 or 150 american. I'm gonna look at the downeys but those ones look nicer.
Ooo me likes the downey flattops. Any other pictures around?
Ooo me likes the downey flattops. Any other pictures around?
Last edited by Stomis; 06-07-2007 at 12:01 PM.
#7
Registered User
Last edited by norcalsvx; 06-07-2007 at 03:54 PM.
Trending Topics
#8
Registered User
Join Date: Jan 2007
Location: Chico Republic, NOR*CAL
Posts: 1,987
Likes: 0
Received 0 Likes
on
0 Posts
#11
Registered User
Join Date: Jan 2007
Location: Chico Republic, NOR*CAL
Posts: 1,987
Likes: 0
Received 0 Likes
on
0 Posts
ya but yours are homemade and made with love right? that IS why i should buy from you right???
#12
Registered User
Our Fiberglass products fall under the North American Free Trade Agreement ( NAFTA ) so no taxes will be assessed . There will ,however , be a broker fee of aprox. $85.00 (max.) to cross the border .
Fred
#13
Registered User
Join Date: Jan 2007
Location: Chico Republic, NOR*CAL
Posts: 1,987
Likes: 0
Received 0 Likes
on
0 Posts
#14
Registered User
Thread Starter
Join Date: Jan 2007
Location: Point Pleasant NJ
Posts: 628
Likes: 0
Received 0 Likes
on
0 Posts
So what does it wind up being for those fenders from canada? Like $500 in the end?
We'll see. My truck goes into phase two this fall. It'll have the SAS done, motor knock fixed, and rear lift properly done. Phase 2 is sliders, finish my flatbed with a rollbar, tube bumper, fenders, and partial exocage.
We'll see. My truck goes into phase two this fall. It'll have the SAS done, motor knock fixed, and rear lift properly done. Phase 2 is sliders, finish my flatbed with a rollbar, tube bumper, fenders, and partial exocage.
#15
Registered User
Thread
Thread Starter
Forum
Replies
Last Post
live4soccer7
84-85 Trucks & 4Runners
3
05-11-2016 06:52 PM
87SR5justin
General Vehicle Related Topics (Non Year Related)
1
09-29-2015 02:50 PM
FS[PacNorWest]: 1987 4Runner SAS, 22RE, 5Spd, Dual Cases, etc
toyotasaurus
Vehicles - Trailers (Complete)
0
09-24-2015 03:30 PM